ADC X21 Manual de usuario Pagina 10
- Pagina / 103
- Tabla de contenidos
- MARCADORES
- ADCP-50-304 1
- Issue 19 1
- June 1999 1
- 1059311 Rev A 1
- COPYRIGHT 2
- TRADEMARK INFORMATION 2
- DISCLAIMER OF LIABILITY 2
- TABLE OF CONTENTS 3
- REVISION HISTORY 7
- ABOUT THIS MANUAL 7
- RELATED PUBLICATIONS 8
- ADMONISHMENTS 8
- GENERAL SAFETY PRECAUTIONS 9
- FCC COMPLIANCE STATEMENT 9
- INTRODUCTION 10
- SECTION 1: INTRODUCTION 11
- 2 PURPOSE AND SCOPE 12
- Page 1-3 13
- * Requires Power Supply 13
- Page 1-4 14
- 2.2 PatchSwitch Equipment 15
- Page 1-6 16
- Page 1-7 17
- Page 1-8 18
- 3 SPECIFICATIONS 19
- 3.1 DMPS-10 AC Power Supply 19
- FUNCTIONAL 20
- DESCRIPTION 20
- 1 GENERAL 21
- FRONT PANEL 22
- CONNECTIONS 22
- BACKPLANE 22
- Page 2-4 24
- Page 2-5 25
- Page 2-6 26
- Page 2-7 27
- Page 2-8 28
- Page 2-9 29
- Page 2-10 30
- TIME DELAY 31
- Page 2-12 32
- Page 2-13 33
- 7.1 Patch Interface (PSM-08) 34
- 8 TEST MODULE (PSM-12) 35
- 9 TEST MODULE (PSM 13) 36
- Page 2-17 37
- 11 PS CHASSIS POWER 38
- PATCHSWITCH V.35 39
- SECTION 3: PATCHSWITCH V.35 40
- Page 3-2 41
- V.35 PIN NAME ORIGIN 42
- CONNECTOR PIN 42
- 3 FUNCTION SELECTION-MODULES 43
- Page 3-5 44
- Page 3-6 45
- Page 3-7 46
- 5 HARDWARE INSTALLATION 47
- Page 3-9 48
- PATCHSWITCH X.21 49
- SECTION 4: PATCHSWITCH X.21 50
- 2 DESCRIPTION 51
- Page 4-3 52
- Page 4-4 53
- 3 FUNCTIONAL DESCRIPTION 54
- 3.1 A/B Switch Modules 54
- 3.2 Switch Module Interlocks 55
- 3.4 Status Indication Modules 56
- 3.5 Alarm Modules 56
- 3.6 Alarm Reset 56
- 3.7 Alarm Time Delay 57
- 3.8 B Alarm Enable/Disable 58
- 4 POWER REQUIREMENTS 58
- 5 SPECIFICATIONS 59
- 6 INSTALLATION 59
- 6.2 Alarm Jumper Installation 60
- 6.3 Alarm Time Delay Setting 61
- 6.4 Adapter Installation 61
- 6.5 Module Installation 61
- 6.6 Cable Connections 61
- SITE PREPARATION 62
- SECTION 5: SITE PREPARATION 63
- Page 5-2 64
- INSTALLATION 65
- SECTION 6: INSTALLATION 66
- 1.3 Blank Panel Installation 67
- Page 6-3 68
- Page 6-4 69
- PS CHASSIS 70
- ADDRESS1 2 3 4 70
- Page 6-6 71
- Page 6-7 72
- 4.2 Alarm Jumper Installation 73
- Figure 6-7. Jumper Locations 74
- OPERATION 75
- SECTION 7: OPERATION 76
- 2.1 Monitor Patching 77
- 2.2 Intrusive Patching 77
- 4.1 Test Module 78
- 5 SWITCHING 78
- 4 INTERFACE MODULE 78
- 6.2 Single Channel Switching 79
- 6.3 Bank Switching 80
- 6.4 Reset Alarms 80
- 6.6 Remote Control Switching 81
- 6.7 Remote Control Commands 81
- 6.8 Command Conventions 81
- 6.9 Command Flags 82
- 6.10 Command Interpretation 82
- 6.11 Command Responses 83
- 6.12 Command Descriptions 83
- 6.14 GO Command 84
- 6.17 Status Responses 85
- 6.18 TLKxx Format 85
- Page 7-11 86
- 6.19 TLKxx Execution 87
- Page 7-13 88
- Page 7-14 89
- Table 7-2 90
- Page 7-16 91
- Page 7-17 92
- 6.20 SPKxx Format 93
- COMMAND STRING 95
- 6.26 Error Codes 98
- Page 7-24 99
- GENERAL INFORMATION 100
- 1 WARRANTY/SOFTWARE 101
- 5 RETURNED MATERIAL 102
- 3 REPAIR CHARGES 102
- 4 REPLACEMENT/SPARE PRODUCTS 102
Relacionado con productos y manuales para Los conmutadores de red ADC X21
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales