Adc Campus-REX2 RS Manual de usuario Pagina 114
- Pagina / 166
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 7 - Using the LCD for Configuration and Management
102 Campus-REX2 RS Interface Card User Manual
2 To select the transceiver mode:
a Press Next until XCVR Mode is displayed.
b Press Enter.
c Press Next until your choice is displayed:
• Master initiates the HDSL link. The other Campus unit must
be set to Slave or Auto.
• Slave waits for the other Campus unit to initiate the HDSL
link. The other unit must be set to Master or Auto.
• Auto (default) automatically switches between Master and
Slave until an HDSL link is established.
The Transceiver Mode option determines the hierarchy of the two
Campus units when attempting to establish an HDSL link.
d Press Enter.
3 To configure LOOP MODE, do the following:
a Press Next to display LOOP MODE.
b Press Enter.
c Press Next to change the setting from 1 Loop (default) to 2 Loop,
then press Enter. The LCD displays LOOP MODE=2 Loops.
4 To configure HDSL RATE, do the following:
a Press Next to display HDSL RATE.
b Press Enter.
It is recommended that you leave the Transceiver Mode
option set to Auto unless you require that a particular end of
the HDSL connection be the Master or Slave.
Also, this value cannot be changed if the HDSL link is up.
- CAMPUS-REX2 RS INTERFACE CARD 1
- VERSION 5.1 1
- FCC NOTICE 3
- USING THIS MANUAL 4
- DOCUMENT CONVENTIONS 4
- Document Conventions 5
- TABLE OF CONTENTS 7
- Table of Contents 10
- Table of Contents 11
- INSTALLING AND 13
- ACCESSING THE REX2 13
- INSTALLING THE CAMPUS-REX2 14
- Guide rail 15
- Campus-REX2 RS 15
- Interface card 15
- Campus-REX2 RS Interface card 16
- CONNECTING THE ETHERNET LINE 17
- Category 5 cable 18
- Black cable 21
- (Category 3) 21
- PairGain 23
- LOGGING IN 24
- Circuit ID: 25
- LOGIN PASSWORD > 25
- REMOTE_LOGON PASSWORD > 27
- LOGGING OFF 28
- USING THE MENUS 28
- OPERATING WITH DEFAULT VALUES 29
- CONFIGURING 31
- HDSL PARAMETERS 31
- CONFIGURING HDSL PARAMETERS 32
- Selecting HDSL Parameters 33
- Using Standard Mode 34
- Using Extended Mode 35
- CONFIGURING HDSL ALARMS 38
- Setting HDSL Alarms 39
- CONFIGURING THE REX2 41
- TATUS SCREEN 42
- Configuring Bridge Features 44
- Viewing Spanning Tree Status 48
- Viewing the Bridge Table 53
- Viewing the ARP Table 54
- Configuring Routing Features 58
- Configuring the IP Addresses 59
- Configuring RIP 61
- Configuring DHCP Services 65
- Accessing the Routing Tables 68
- ANAGEMENT 72
- Entering SNMP Parameters 73
- Configuring Trap Receivers 75
- MANAGING 77
- SYSTEM PARAMETERS 77
- CCESSING SYSTEM CONFIGURATION 78
- SETTING THE TIME AND DATE 79
- SETTING A PASSWORD 81
- RESTORING DEFAULT VALUES 82
- Are You Sure (Y/N) ? y 83
- Hit Any Key to Continue 83
- VIEWING PRODUCT INFORMATION 84
- MONITORING AND TESTING 85
- CAMPUS SYSTEM 85
- MONITORING HDSL PERFORMANCE 86
- Viewing Local Alarm History 91
- VIEWING ETHERNET STATISTICS 92
- Viewing Bridge Statistics 93
- Viewing Router Statistics 95
- PERFORMING TESTS 97
- Performing Loopback Testing 99
- RESETTING THE CAMPUS UNIT 101
- MANAGING SOFTWARE 103
- PGRADING CAMPUS UNIT SOFTWARE 104
- RECOVERING SOFTWARE 107
- MANAGEMENT 109
- USING THE LCD FOR 109
- CONFIGURATION 109
- NAVIGATING THE LCD MENUS 110
- SETTING THE HDSL PARAMETERS 111
- Configuring Standard Mode 112
- CONFIGURING THE CAMPUS-REX2 115
- Configuring REX2 Parameters 116
- Setting the Encapsulation 117
- Setting Bridge Configuration 118
- Setting Router Configuration 119
- Saving the REX2 Configuration 120
- IEWING AND CONFIGURING ALARMS 121
- Configuring Alarm Thresholds 122
- Local Alarms 123
- Remote Alarms 124
- CONFIGURING LOOPBACKS 125
- Initiating a Loopback 126
- Clearing a Loopback 126
- Setting the Loopback Timeout 126
- VIEWING SYSTEM INFORMATION 127
- VIEWING STATUS INFORMATION 127
- PORT STATISTICS 128
- Bridge Port Statistics 129
- Router Port Statistics 130
- INTERNETWORKING AND 131
- MANAGEMENT OVERVIEW 131
- APPLICATION 133
- Point-to-Point LAN Extension 134
- LAN Connections Over a WAN 135
- About MAC-Level Bridging 136
- About Spanning Tree Protocol 136
- Example Physical Network* 137
- Loop-free Topology 137
- Using Spanning Tree Protocol 137
- IP ROUTING 138
- Dynamic Routing 141
- Campus-REX2 IP Addresses 141
- Internet 143
- MANAGEMENT PROTOCOLS 144
- MIB AND TRAP SUPPORT 145
- ENCAPSULATION PROTOCOLS 147
- RODUCT COMPATIBILITY 148
- TECHNICAL REFERENCE 151
- DEFAULT SETTINGS 152
- ETHERNET PORT 153
- STANDARDS 153
- ABBREVIATIONS 155
- Appendix B - Abbreviations 156
- CONTACTING ADC 157
- Appendix D - Contacting ADC 158
- Numerics 159
- ART NUMBER: 1269224 166
Relacionado con productos y manuales para Hardware Adc Campus-REX2 RS
Hardware Adc FTTX Service Pack Manual de usuario
(4 paginas)
(4 paginas)
Hardware Adc ISDN NT11010 Manual de usuario
(24 paginas)
(24 paginas)
Hardware Adc LoopStar 750 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Adc ETP-64 Manual de usuario
(2 paginas)
(2 paginas)
Hardware Adc FlexWave MMX 6000 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Adc Soneplex P-61-743 Manual de usuario
(30 paginas)
(30 paginas)
Hardware Adc FlexWave MMW 110 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Adc 400F Manual de usuario
(114 paginas)
(114 paginas)
Hardware Adc OmniReach oFDT-48 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Adc Baluns Series Manual de usuario
(5 paginas)
(5 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales