ADC Cuda 12000 Guía de instalación Pagina 119
- Pagina / 168
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Cuda 12000 IP Access Switch Installation Guide
Connecting Power 119
Replacing Fan Tray Fuse Cartridges
The power connector unit consists of four threaded power studs and two
slow-blow class 2 fuse cartridges. If one or both of the fuses blow,
replacement of the fuse cartridge is necessary. To replace a blown fuse,
follow this procedure:
1. If you haven’t already done so, review “Electrical Safety Guidelines and
Precautions” on page 59.
2. Remove the power connector cover located on the rear panel of the fan
tray unit by loosening the four screws that secure the cover, as shown in
Figure 5-17.
3. Locate the blown fuse and remove it.
4. Replace the fuse with a 2 1/2 Amp 250 Volt slow-blow fuse only.
5. Cover the power connectors with the power connector cover, ensuring
that the wires are properly placed through the opening at the bottom of
the cover. Then place the wires through the cable clamp, as shown in
Figure 5-18.
- Cuda 12000 IP Access Switch 1
- Installation Guide 1
- 8 Technology Drive 3
- Westborough, MA 01581 3
- CONTENTS 5
- 2 PREPARING FOR INSTALLATION 6
- 3 RACK-MOUNTING THE SYSTEM 6
- 4 INSTALLING MODULES 7
- 5 CABLING THE SYSTEM 7
- A CONFIGURING NETWORK ACCESS 8
- C MARTEK POWER SUPPLY 8
- D WIRING DIAGRAMS 8
- E GLOSSARY 8
- ABOUT THIS GUIDE 9
- Document Organization 10
- Notations 11
- Related Documentation 11
- then select the 12
- HARDWARE OVERVIEW 13
- 1: HARDWARE OVERVIEW 14
- Feature Description 14
- System Overview 15
- Routing Support 16
- Backplane Connections 17
- The Cooling System 17
- Front View 18
- Rear View 19
- Component Description 20
- Interior View 21
- Management Module 22
- Management Module 23 23
- HAPTER 1: HARDWARE OVERVIEW 24
- Application Modules 25
- Application Module Features 26
- Application Module Components 26
- ■ DOCSIS modules 27
- ■ EuroDOCSIS modules 27
- Component Description 28
- DOCSIS Modules 29
- 1.1 specifications 30
- 1x4 DOCSIS SpectraFlow Module 31
- Management 33
- EuroDOCSIS Modules 35
- Application Modules 37 37
- EuroDOCSIS specification 38
- Egress Modules 41
- LED Description 42
- ■ Min: -9.5 dBm 44
- ■ Max: -3 dBm 44
- ■ Min: -20 dBm 44
- Application Modules 45 45
- Fan Tray 49
- Outgoing Air Stream 51
- Incoming 51
- Air Stream 51
- Filtering 53
- Thumbscrews (2) 53
- Ethernet Patch Panel 54
- Ethernet Patch Panel 55 55
- PREPARING FOR INSTALLATION 57
- Safety Guidelines 58
- Safety Guidelines 59 59
- Site Requirements 60
- Tools for Installation 61
- RACK-MOUNTING THE SYSTEM 63
- System Placement in the Rack 64
- 3: RACK-MOUNTING THE SYSTEM 66
- Rack-Mount Order 68
- THIS SIDE UP 69
- Rack-Mounting the Chassis 71
- Rack-Mounting the Chassis 73 73
- Screws (4) 75
- (3.5 in.) 75
- INSTALLING MODULES 77
- Filler Panels 78
- 12345678910111213 78
- Backplates 78
- 1112 10 9 8 7 6 5 4 3 2 1 78
- Slot Modules Accepted 79
- Replacing a Filler Panel 81
- Figure 4-4 82
- 12000 uses 84
- Removing a Backplate 85
- Replacing a Backplate 85
- 4: INSTALLING MODULES 86
- Installing System Modules 87
- Installing System Modules 89 89
- Removing Modules 90
- Removing Modules 91 91
- CABLING THE SYSTEM 93
- Cabling for Serial Access 94
- To Computer or 95
- COM Server 95
- To Modem 96
- BAC_53com2 97
- MDI Port on 99
- Network 99
- ADC Telecommunications, Inc 100
- 5: CABLING THE SYSTEM 100
- Patch Panel 106
- RJ45 Cable 106
- RJ45 Connectors (24) 106
- SpectraFlow Modules 107
- Connecting Power 109
- Connecting Power 111 111
- Studs (4) 113
- Connecting Power 115 115
- Power Studs (4) 117
- Connecting Power 119 119
- POWERING ON AND POWERING OFF 125
- Observing LED Activity 126
- Powering Off the System 131
- Basic Troubleshooting 133
- CONFIGURING NETWORK ACCESS 135
- Configuring Network Access 136
- Security Considerations 137
- IPChains 138
- SYSTEM SPECIFICATIONS AND 139
- COMPLIANCE 139
- MARTEK POWER SUPPLY 141
- Basic Troubleshooting 143 143
- C: MARTEK POWER SUPPLY 144
- WIRING DIAGRAMS 145
- COM Modem Cable Assembly 146
- Cabling for Fault Reporting 147
- D: WIRING DIAGRAMS 148
- GLOSSARY 149
- E: GLOSSARY 150
- so that 155
Relacionado con productos y manuales para Los conmutadores de red ADC Cuda 12000
Los conmutadores de red ADC X21 Manual de usuario
(103 paginas)
(103 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales